How to Configure Cisco Router and Switch Step by Step

To configure a Cisco Packet Tracer project where a router connects to a switch with two VLANs (VLAN10 and VLAN20), and each VLAN has its subnet, follow these steps:

Network Design:

Router:

Interface: gi0/0 connected to the switch.
Sub-interfaces configured for each VLAN with IP addresses for inter-VLAN routing.

Switch:

VLAN10 and VLAN20 created.
Ports assigned to each VLAN for devices on each subnet.
The port connected to the router set as a trunk.

Step-by-Step Configuration:

1. Configure VLANs on the Switch

Access the Switch CLI:

   Switch> enable
   Switch# configure terminal
   Switch(config)#hostname SkyFada-S

Create VLAN10 and VLAN20:

   SkyFada-S(config)# vlan 10
   SkyFada-S(config-vlan)# name VLAN10
   SkyFada-S(config-vlan)# exit

   SkyFada-S(config)# vlan 20
   SkyFada-S(config-vlan)# name VLAN20
   SkyFada-S(config-vlan)# exit

Example as below:

Assign Ports to VLANs (assuming you have two clients, one for each VLAN):

   SkyFada-S(config)# interface fa0/1
   SkyFada-S(config-if)# switchport mode access
   SkyFada-S(config-if)# switchport access vlan 10
   SkyFada-S(config-if)#no shutdown
   SkyFada-S(config-if)#do wr
   SkyFada-S(config-if)# exit

   SkyFada-S(config)# interface fa0/2
   SkyFada-S(config-if)# switchport mode access
   SkyFada-S(config-if)# switchport access vlan 20
   SkyFada-S(config-if)#no shutdown
   SkyFada-S(config-if)#do wr  
   SkyFada-S(config-if)# exit

Configure Trunk Port on the switch to connect to the router:

   SkyFada-S(config)# interface gi0/1
   SkyFada-S(config-if)# switchport mode trunk
   SkyFada-S(config-if)#no shutdown 
   SkyFada-S(config-if)#do wr
   SkyFada-S(config-if)# exit

Save all configuration

SkyFada-S#copy running-config startup-config

How to Configure Cisco Router and Switch Clients Can Access to VLAN Plan

2. Configure the Router

Access the Router CLI:

   Router> enable
   Router# configure terminal
   Router(config)#hostname SkyFada-R

Configure Sub-interfaces for Each VLAN:

On the router’s gi0/0 interface, create sub-interfaces for VLAN10 and VLAN20. Assign IP addresses to the sub-interfaces. Encapsulate each sub-interface with the appropriate VLAN ID.

   SkyFada-R(config)# interface gi0/0.10
   SkyFada-R(config-subif)# encapsulation dot1Q 10
   SkyFada-R(config-subif)# ip address 10.1.1.1 255.255.255.0
   SkyFada-R(config-subif)#description Vlan10
   SkyFada-R(config-subif)# do wr
   SkyFada-R(config-subif)# exit

   SkyFada-R(config)# interface gi0/0.20
   SkyFada-R(config-subif)# encapsulation dot1Q 20
   SkyFada-R(config-subif)# ip address 192.168.0.1 255.255.255.0
   SkyFada-R(config-subif)#description Vlan20
   SkyFada-R(config-subif)# do wr
   SkyFada-R(config-subif)# exit

Enable the Router Interface:

   SkyFada-R(config)# interface gi0/0
   SkyFada-R(config-if)# no shutdown
   SkyFada-R(config-if)# exit

3. Configure Static IP for Clients

Connect a PC to fa0/1 for VLAN10 and another PC to fa0/2 for VLAN20.

PC in VLAN10: Assign IP Address to PC

IP Address: 10.1.1.X (e.g., 10.1.1.10)
Subnet Mask: 255.255.255.0
Default Gateway: 10.1.1.1

Cisco Business CBS220-8P-E-2G Smart Switch | 8 Port GE | PoE

PC in VLAN20:

For the PC2 in VLAN20, you can follow steps 1 in VLAN10

IP Address: 192.168.0.X (e.g., 192.168.0.10)
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.0.1

4. Test Connectivity

Use the ping command from each PC to test connectivity with its VLAN gateway.
Ensure PCs in VLAN10 and VLAN20 cannot communicate directly. They should reach the router’s respective sub-interface IP addresses for inter-VLAN routing, if configured.

After assigning the IP Address you should ping test to make sure it working or not

This setup enables clients in VLAN10 and VLAN20 to access their designated networks with static IP addresses. You can now ping as well. Learn more…

Cisco CCNA course duration

For most people, anywhere from 3 to 6 months of dedicated study is realistic. This timeframe allows them to go from zero knowledge to being prepared for the CCNA exam.

Fast Learner (with some IT experience): ~2-3 months
Dedicated Beginner (no IT experience): ~4-6 months
Studying Part-Time (busy schedule): 6+ months

Factors That Influence Your Timeline

Prior Experience:
- No IT background: You’ll need to learn fundamental concepts from scratch, which will take longer. Plan for the 5-6 month range.
- Some IT/Networking knowledge: If you already understand basic concepts like IP addresses, DHCP, or DNS, you have a head start. You might fit into the 3-4 month range.
- Experienced but uncertified: If you’ve been working with networks for years, you might just need the credential. In that case, you could be ready in 1-2 months. You only need to brush up on the specifics.
Study Time Commitment:
- Full-Time Student: If you can treat studying like a full-time job, plan to study 6-8 hours a day. This approach allows you to compress the timeline significantly.
- Working Professional: This is the most common scenario. If you can consistently dedicate 1.5 – 2 hours on weekdays. Dedicate 3-4 hours on weekends. Total approximately 15 hours per week. Then you can achieve the 4-5 month range.
Learning Method:
- Self-Study (Video Courses, Books): This is the most flexible and common path. The pace is entirely up to you.
- Bootcamps: Intensive, instructor-led bootcamps can cover all the material in 1-2 weeks. However, they require full-time attendance. They are also very expensive. They are best for quickly consolidating knowledge, not necessarily for learning from zero.
- Formal Education: A college course might spread this material over a full semester (3-4 months).

Realistic 5-Month Study Plan

This plan assumes you’re studying 15-20 hours per week.

Month 1: Networking Fundamentals
- Topics: TCP/IP and OSI models, IPv4 and IPv6 addressing, subnetting, network media (cables, Wi-Fi).
- Focus: Master subnetting. This is the most critical foundational skill. Don’t move on until you can do it quickly.
Month 2: Network Access & IP Connectivity
- Topics: Ethernet, VLANs, STP, basic router and switch configuration.
- Focus: Get hands-on experience with the CLI. Use a simulator like Cisco Packet Tracer (free!) or a virtual lab.
Month 3: IP Services & Security Fundamentals
- Topics: DHCP, DNS, NTP, ACLs (Access Control Lists), NAT (Network Address Translation).
- Focus: Understand how these services work together in a network.
Month 4: Automation and Programmability
- Topics: Network management, SDN (Software-Defined Networking), APIs, REST, configuration management tools.
- Focus: Don’t be intimidated by this section. You don’t need to be a programmer; you need to understand the concepts.
Month 5: Review, Practice, and Exam Prep
- Activities: Take numerous practice exams (from Boson, Pearson, etc.), review your weak areas, lab relentlessly to solidify configurations and troubleshooting skills.
- Focus: Troubleshooting. The modern CCNA exam heavily tests your ability to figure out what’s wrong in a network.

Cisco Business CBS220-8P-E-2G Smart Switch | 8 Port GE | PoE

Crucial Advice for Success

Get Hands-On: Reading and watching videos is not enough. You must lab. Cisco Packet Tracer is free and perfect for the CCNA. Build networks, break them, and fix them.
Use Multiple Resources: Don’t rely on just one book or video series. Different instructors explain things in different ways. Popular choices include:
- Video Courses: Neil Anderson (CBT Nuggets), Jeremy’s IT Lab (free on YouTube), Keith Barker.
- Books: Official Cert Guide by Wendell Odom.
- Practice Exams: Boson ExSim is considered the gold standard.
Understand, Don’t Memorize: The CCNA exam tests your ability to apply concepts, not just recall facts. If you understand the “why,” you can answer any question.

Set a goal of 4-6 months. Create a consistent study schedule. Get plenty of hands-on practice. You will be well on your way to earning your CCNA. Good luck

Discover more from SkyFada

Subscribe to get the latest posts sent to your email.

Subscribe to Updates

How to Configure Cisco Router and Switch Clients Can Access to VLAN Plan